Funny I already posted here some 100 photos and I only trim the photos if by tapatalk, by the site was not ca foto no !!!!!
Where can I get online? by the tlm?
Enviado do meu GT-I9060I através do Tapatalk
Re: pcx power-full
Posted: Tue Dec 04, 2018 7:20 pm
by Mel46
I think you have saved a great bike from a horrible death, and you have given it a great future. What did you do about the ecu? Did it need something running piggyback or did the ecu just reset and adjust to the bigger kit?
Re: pcx power-full
Posted: Wed Dec 05, 2018 6:15 am
by power-full
Mel46 wrote:I think you have saved a great bike from a horrible death, and you have given it a great future. What did you do about the ecu? Did it need something running piggyback or did the ecu just reset and adjust to the bigger kit?
good in the motorcycle ecu I did not do anything (was it to do anything?)
I just put up a box that connects to the throttle of the admission, and secondly, I noticed this box fools the probe lick ..
Enviado do meu GT-I9060I através do Tapatalk
Re: pcx power-full
Posted: Wed Dec 05, 2018 6:32 am
by power-full
the electrical scheme of this box and
This is the photo. the new box (new model what I have) is no longer necessary to cut anything, just plug in chips
Very good!
How has it been running since the upgrade? Just the fact that it is running at all is great.
Re: pcx power-full
Posted: Thu Dec 06, 2018 12:43 am
by power-full
has worked well, walks well, pulls well, spends well. haha
I am with lack of time .... I have the variator yuminashi and the gearbox (reels) longer to mount. ..
Enviado do meu GT-I9060I através do Tapatalk
Re: pcx power-full
Posted: Thu Dec 06, 2018 12:49 am
by power-full
I have in view more these 2 pieces and I think that I will stay here ..
the exhaust and the camshaft.
Hi good morning everyone. for some time that I went through here, until I see everything ok with the pcx, at the end of January I more or less bought the yuminashi variator kit, and I'm still adapting to it. lol. I missed 1000 km for the review, at that time I am going to change the clutch springs for the yuminashi a .. what I had assembled before was everything malossi both variador and springs. here are some of the photos
Edited by WN 3.13.19 added video
Note to power-ful to add your youtube video or any youtube video:
click on the youtube button found above the message box (that your replying/typing in) then go to your video and cut the letters, numbers etc. found After the = sign. Go back to message and paste it in-between the youtube brackets you created earlier.
As an example: In your video shown above, I cut and pasted these letters and numbers: t0tqAO3CAXw (found on your youtube video page) and placed them/pasted them between the center brackets of this: [youtube][/youtube]. Then click submit and Bingo! Movie Time
I hope this helps you and others reading. Cheers and keep on tooling (o:
Edited by WN 3/13/19: Added Video
See, I did it again You can too!
Re: pcx power-full
Posted: Fri Mar 15, 2019 5:28 am
by power-full
Thanks
Enviado do meu 6055K através do Tapatalk
Re: pcx power-full
Posted: Mon Apr 01, 2019 1:42 am
by power-full
Yesterday was another day of review ... Brake oil (dot 5.1), antifreeze g12 (pink), engine oil (Castrol racing 5w40) check rollers, strap, pads and lights .. It is ready for another 4000km. .
power-ful, sorry but your images are too large to process.
I saw a warning box above your photo's that stated: "Your images may only be up to 768 pixels high."
Try sizing them down.
As far as entering photos via tapatalk....it's unknown territory to me.
You can too! 
