Page 8 of 9
Re: pcx power-full
Posted: Sat Feb 12, 2022 3:32 am
by Valeriy7
power-full wrote: ↑Sat Feb 12, 2022 2:31 am
the gasket must always be new. because the joint comes with a height to be crushed when it is tightened that's what makes the seal.
when assembling the new gasket you must start the motorcycle for 5 to 10 minutes stopped in place to warm up the engine and open the thermostat, to picture the circuit. I usually do it like this: I fill the radiator with antifreeze, put the radiator cap on (be careful it cannot be the original cap which is 0.9 bar, it has to be 1.6 bar) I start the bike at idle, then I start accelerating around 30/40 Kh or so and I'm putting my hand on the down tube that comes to the radiator (be careful not to touch the exhaust tube) when the radiator tube starts to get hot turn off the engine. after about 30/40 minutes, open the radiator cap, refill the level as needed (almost always accurate), put antifreeze in the expansion vessel and good curves....
Thank you very much! I have done this before with the lid open, adding gas until air bubbles come out. Lid 1.6 bar.
Re: pcx power-full
Posted: Sun Feb 13, 2022 4:49 am
by power-full
you shouldn't do it with the lid open that works fine on big circuits not here on this one so small..
Re: pcx power-full
Posted: Sun Feb 13, 2022 9:46 am
by Valeriy7
power-full wrote: ↑Sun Feb 13, 2022 4:49 am
you shouldn't do it with the lid open that works fine on big circuits not here on this one so small..
Thanks! I'll be taking the engine apart soon. We still have frost and snow, waiting for the heat.
Re: pcx power-full
Posted: Mon Feb 14, 2022 4:05 pm
by ToraxOutlaw
Where did you get the LED headlights and sidelights from?
Re: pcx power-full
Posted: Mon Feb 14, 2022 4:11 pm
by power-full
ToraxOutlaw wrote: ↑Mon Feb 14, 2022 4:05 pm
Where did you get the LED headlights and sidelights from?
comprei no ebay..vou ver se consigo o link.
https://www.ebay.com/itm/255303776596?h ... SwJ1dhzJCZ
Re: pcx power-full
Posted: Mon Feb 14, 2022 4:19 pm
by power-full
hello guys here are some more pics
Re: pcx power-full
Posted: Mon Feb 14, 2022 4:41 pm
by ToraxOutlaw
How would you connect the H4 bulbs to the HS5 sockets?
aRe: pcx power-full
Posted: Mon Feb 14, 2022 5:04 pm
by power-full
you cut the plug before the socket you leave a little wire for if one day you want to assemble it again, and you have the connections there .. you pass a medium wire to each side and the same with the medium wires
Re: pcx power-full
Posted: Mon Feb 14, 2022 5:06 pm
by ToraxOutlaw
Brilliant. Thanks.
Re: pcx power-full
Posted: Mon Feb 14, 2022 5:24 pm
by ToraxOutlaw
I don't fancy cutting and splicing wires. Are the any kits around that'll convert HS5 to any other bulb type?
Re: pcx power-full
Posted: Tue Feb 15, 2022 8:46 am
by ToraxOutlaw
I'm only asking this as the LEDs you have installed are not road legal for the UK. My bike would fail its MOT.
Re: pcx power-full
Posted: Wed Apr 13, 2022 12:04 am
by power-full
Yesterday was such a weird day. belt had 2000km, all of a sudden on the highway it was like this... I'm back on the road but this time only with 120 kh... I'll have to buy some new parts from yuminashi.
Re: pcx power-full
Posted: Wed Apr 13, 2022 12:07 am
by power-full
Aos 94000km
Re: pcx power-full
Posted: Mon Apr 25, 2022 7:20 am
by power-full
Hello good morning .. this weekend I started assembling the new yuminashi 164cc v2 kit here are some of the photos ..
Re: pcx power-full
Posted: Mon Apr 25, 2022 9:03 am
by mymitzi
Nice clean up...........will you replace with a Honda Belt or have they not been up to the task? Hope you get er going soon.
Re: pcx power-full
Posted: Tue Apr 26, 2022 2:12 am
by power-full
Good Morning. a yuminashi 164cc version 2 kit was assembled. this kit is fitted to 2010 engines up to 2018 engines .. in the non-esp version it is necessary to open the engine casings. an injector is included, I already gave a brief description of what will come out of here.
Re: pcx power-full
Posted: Tue Apr 26, 2022 2:14 am
by power-full
mymitzi wrote: ↑Mon Apr 25, 2022 9:03 am
Nice clean up...........will you replace with a Honda Belt or have they not been up to the task? Hope you get er going soon.
Hi i mounted one of Polini. I have another one of these from gates for this new kit.
Re: pcx power-full
Posted: Tue May 03, 2022 2:56 pm
by power-full
Re: pcx power-full
Posted: Tue May 03, 2022 6:40 pm
by dankly1
power-full wrote: ↑Wed Apr 13, 2022 12:04 am
Yesterday was such a weird day. belt had 2000km, all of a sudden on the highway it was like this... I'm back on the road but this time only with 120 kh... I'll have to buy some new parts from yuminashi.
Any idea what part or parts failed and caused the problem with your variator? Did one of the rollers come apart? Thanks!
dankly
Re: pcx power-full
Posted: Fri May 27, 2022 4:56 am
by power-full
hello good morning guys. I already have the new videos of the new kit assembled on my YouTube page. here is the last yesterday made just for walking I will have to adjust the weights of the variator
https://youtube.com/shorts/f8TzqPll_jA?feature=share
https://youtube.com/shorts/_U4cts3kxfk?feature=share