Need noise

Sahar · Post by **Sahar** » Wed Jun 24, 2015 12:50 pm

Alright, I'm excited for your test

Btw do you ride it in the rain like that?

sendler2112 · Post by **sendler2112** » Wed Jun 24, 2015 1:11 pm

The hole is on the underside. And 1/3 of my 15,000 miles per year is in the rain. Syracuse, NY USA 13066

fun2scoot · Post by **fun2scoot** » Wed Jun 24, 2015 3:38 pm

Sahar wrote:Should I place one hole in the middle , where you drilled 3 of them?
Btw how deep should i drill? ( about 5-10mm)

I'm curious also as to the exact drill spot, but I guess I don't take verbal directions all that well.
If it is not too much trouble, maybe you could use Paint to put a circle where the hole should be and repost.

Alibally · Post by **Alibally** » Wed Jun 24, 2015 4:34 pm

I think it would probably fail an MOT test in the UK. As the exhaust is holed.

fun2scoot · Post by **fun2scoot** » Wed Jun 24, 2015 5:22 pm

Would it work if the hole were drilled, tapped to a known size, thread and pitch, spray zinc, then plugged?

then the plug could be pulled as needed. Say for those heady days at Daytona...

I'll try this as soon as I learn exactly where the hole should be.

sendler2112 · Post by **sendler2112** » Wed Jun 24, 2015 6:01 pm

The metal of the can is thick enough to hold a thread or two but there is not a lot of room between the can wall and the cat to run a tap in if you do it on the underside of the can as I did.

fun2scoot · Post by **fun2scoot** » Wed Jun 24, 2015 7:35 pm

I see. And I would do it from the underside...
thinking, thinking...

Alibally · Post by **Alibally** » Thu Jun 25, 2015 3:17 am

Drill a hole in the correct place, weld a nut on around the hole and hey presto, no need to tap the exhaust ,and 4 or 5 threads for a plug.

Sahar · Post by **Sahar** » Sun Jun 28, 2015 3:43 am

@sendler2112

Could we expect your sound comparison today?

Sahar · Post by **Sahar** » Thu Jul 16, 2015 9:37 am

I guess there will not be a sound comparison?!

sendler2112 · Post by **sendler2112** » Thu Jul 16, 2015 12:09 pm

I was on a 880 mile camping trip on my CBR250R last week. Maybe this weekend I can get a video up.

nicuts · Post by **nicuts** » Sun Aug 21, 2016 12:52 pm

Hi Sendler, your photos how you drilled the exhaust are no longer available, any possibility you can post them again or maybe email them to me,
Tx nico

sendler2112 · Post by **sendler2112** » Sun Aug 21, 2016 8:28 pm

Facebook keeps changing the address of my photos.
.
.

.
.

you you · Post by **you you** » Mon Aug 22, 2016 1:33 am

sendler2112 wrote:Facebook keeps changing the address of my photos.
.
.

.
.

Good group with one pulled shot.

nicuts · Post by **nicuts** » Thu Aug 25, 2016 12:45 pm

Tx Sendler, did you tidy the holes up or just left it as in the photo

sendler2112 · Post by **sendler2112** » Thu Aug 25, 2016 2:13 pm

Just left it. It is pretty loud now. I might recommend going a bit smaller.

nicuts · Post by **nicuts** » Sun Aug 28, 2016 10:27 am

I didn't see the Honda sketch of the internals of the exhaust , but if I drill a 20 mm hole through the tail end of the exhaust and through the first chamber, won't I get the same gains with a neater appearance?

The Honda PCX / Forza / ADV150 / SH Forums

Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Re: Need noise

Re: Need noise