How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Maintenance, guides, and walkthroughs for your PCX. Please do not post questions about repairing or fixing your bike here.

Moderator: Modsquad

User avatar
maddiedog
Benevolent Overlord
Benevolent Overlord
Posts: 3636
Joined: Tue Nov 01, 2011 7:04 pm
Year: 2011
Color: White
Location: New Mexico
Contact:

How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by maddiedog »

This guide describes how to install a big bore kit on your PCX. I would like users to refrain discussing whether or not performance modifications are worthwhile to avoid doing so here; any posts of that nature will be moved to this thread: http://hondapcx.org/viewtopic.php?f=9&t=626

As with any performance mod, your results will vary with your bike. The kit I installed on my PCX is specific to the 2011 Honda PCX 125, and will not fit the eSP model, the 150, or the new 150s. I have much more sustained power uphills, and about an extra 10mph top end after changing out my transmission gearing (How-To for changing transmission gearing is coming soon).

The process for installing the big bore kit is not easy or quick, and assumes that you have already:
1. Completed the How-To: Completely Dismantle A PCX
2. Completed the How-To: Remove the Engine from a Honda PCX
3. Procured a big bore kit and all needed consumables
4. Mentally prepared yourself for potentially destroying your bike if you mess up this procedure

Just like with the engine removal how-to, beer helps. Image


In addition to the tools used in the previous how-tos to get to this point, I used:
- Metric allen wrench set
- Small pick (moving O-Rings, using circlips)
- Feeler gauge
- Hammer drill (FUCKING EVIL OVERTIGHTENED SCREWS :x -- you might not need this)

Honda recommends you use a silly $100 cam chain tensioner. I didn't. I removed the tensioner and allowed it to fully untension, then retensioned it and reinstalled it tensioned. It's still fine 2k miles later. More on that later.


You'll also need the following consumables:
- Coolant (You must drain and refill)
- Oil (You should change the oil after the first mile, then refollow new engine breakin procedures and maintenance schedules, including another oil change at 600 miles, then every 5k miles. You do not actually have to drain the oil during the procedure)
- Rags (for cleaning things, clean lint-free ones to stick in any engine orifices if you need to walk away from the project)
- Carb cleaner (Your head will likely have carbon buildup, you should clean that before installing it)
- Sealing compound for the valve cover gasket around the water pump


Here's the parts we'll be installing today:
IMG_7500.JPG
IMG_7500.JPG (361.83 KiB) Viewed 18183 times

From left to right: piston rings and pin, cylinder, camshaft, gaskets, fuel injector (bottom right). The gear in the top-right will be installed in another tutorial (How-To: Upgrade Transmission Gearing).

A close-up of the cylinder. This is a Takegawa kit, and seems higher quality than the stock Honda components. Again, note that this kit is DIFFERENT than the one for the 150s and 125 eSP, because the cylinder and head is different for those revisions. This kit will ONLY work on the original 2011 Honda PCX revision 1.
IMG_7501.JPG
IMG_7501.JPG (280.03 KiB) Viewed 18183 times

A close-up of the camshaft (I still need to install mine, more on that later):
IMG_7502.JPG
IMG_7502.JPG (328.49 KiB) Viewed 18183 times

A close-up of the injector. Mine was branded as "MADMAX," but it's a OEM honda part from another bike:
IMG_7690.JPG
IMG_7690.JPG (256.74 KiB) Viewed 18183 times

You should be starting with your engine off the bike. I had Freedog muscle the engine onto a toolbox (he's built like a bear). The assembly probably weighs 100lbs, which I can lift, but would rather not. If you're puny like me, have a friend around to help.
IMG_7648.JPG
IMG_7648.JPG (306.19 KiB) Viewed 18183 times

If you haven't already, first start by draining the coolant. The drain plug is in the bottom-middle of the radiator. There will be a bit of fluid left in the piping, so I grabbed my coffee mug, undid the clamps, and drained the fluid in the tubes out.
IMG_7652.JPG
IMG_7652.JPG (228.22 KiB) Viewed 18183 times
IMG_7653.JPG
IMG_7653.JPG (211.85 KiB) Viewed 18183 times
IMG_7654.JPG
IMG_7654.JPG (191.65 KiB) Viewed 18183 times

With that out of the way, undo the radiator shroud then the radiator to be able to check if the engine is at top dead center. If I'm remembering correctly, the shroud had 3 bolts and so did the radiator.
IMG_7657.JPG
IMG_7657.JPG (280.28 KiB) Viewed 18183 times
IMG_7659.JPG
IMG_7659.JPG (282.38 KiB) Viewed 18183 times

You can see the radiator fan. It's directly bolted to the crankshaft, so spinning the fan pushes or pulls the piston accordingly, turning over the engine.
IMG_7661.JPG
IMG_7661.JPG (250.37 KiB) Viewed 18183 times

Looking closer, you can see an arrow on the left and a notch. Spin the fan until the notch lines up with the arrow.
IMG_7662.JPG
IMG_7662.JPG (221.45 KiB) Viewed 18183 times

At this point, the piston is in top dead center, but you need to make sure the valves are fully closed. To check that, remove the valve cover. Start by popping off the hose on the top, then remove the 3 bolts.
IMG_7664.JPG
IMG_7664.JPG (265.46 KiB) Viewed 18183 times
IMG_7666.JPG
IMG_7666.JPG (265.19 KiB) Viewed 18183 times

Wiggle the rocker arms on top of the valve springs. If they are solid and don't move, you must rotate the fan another 360 degrees because the engine is on the wrong part of the stroke. Rotate the fan around and check again. The rocker arms should have a bit of wiggle. Again, YOU MUST HAVE SOME WIGGLE. Seriously, double-check. If you don't get this step right, your engine may meet your piston during disassembly, which would basically be like setting off a small grenade in there.
IMG_7667.JPG
IMG_7667.JPG (271.88 KiB) Viewed 18183 times

When you're triple sure your engine is at top dead center (did you check again? WIGGLE THAT ARM!), remove the water pump and the hose with it (5 or 6 bolts total for the assembly):
IMG_7674.JPG
IMG_7674.JPG (216.59 KiB) Viewed 18183 times
IMG_7676.JPG
IMG_7676.JPG (231.96 KiB) Viewed 18183 times

The top comes off first...
IMG_7680.JPG
IMG_7680.JPG (187.65 KiB) Viewed 18183 times

Then slide the pump base off the camshaft. It takes a good tug to get it undone.
IMG_7681.JPG
IMG_7681.JPG (266.23 KiB) Viewed 18183 times

You can now see the side of the cam chain gear.
IMG_7682.JPG
IMG_7682.JPG (262.52 KiB) Viewed 18183 times

Looking closely, it should look just like this in top dead center. Remember that -- it'll be important later for when we have to put the cam chain on afterwards.
IMG_7699.JPG
IMG_7699.JPG (255.04 KiB) Viewed 18183 times

We need to get the FI system off of the cylinder next. Unbolt the two bolts on either side of the injector and pull the whole intake system (injection, throttle body, and air filtering system) back up and away from the cylinder:
IMG_7685.JPG
IMG_7685.JPG (266.64 KiB) Viewed 18183 times
IMG_7686.JPG
IMG_7686.JPG (275.51 KiB) Viewed 18183 times

On my PCX, there was a spacer with an o-ring, and an o-ring. Make sure you don't lose either.

The spacer goes o-ring side down towards the cylinder:
IMG_7694.JPG
IMG_7694.JPG (218.23 KiB) Viewed 18183 times

And the o-ring stayed attached to the intake setup, as shown below:
IMG_7687.JPG
IMG_7687.JPG (184.07 KiB) Viewed 18183 times

Speaking of the intake system, it's time to change the injector. When you upgrade to a big bore kit, the FI system can only compensate so much with the stock injector. Upgrading to one with bigger jets allows more fuel in, allowing the engine to use that extra displacement for more power, and preventing a lean condition from having too little fuel combusting in the chamber.

The injector is held on by the two blue bolts. Remove them.
IMG_7688.JPG
IMG_7688.JPG (230.85 KiB) Viewed 18183 times

The bottom side of the injector, removed.
IMG_7689.JPG
IMG_7689.JPG (202.62 KiB) Viewed 18183 times

Pull the injector out of its mount, click the new one in, and reinstall. Make sure the new one has the same thick sealing o-ring as the original. Reinstall the injector in the intake system, but leave the intake detached.

The ignition system is mounted to the cylinder, remove that next. It's on the left side of the bike. Remove the plug off the sparkplug, and pull the ignition coil off with the two bolts securing it:
IMG_7695.JPG
IMG_7695.JPG (273.21 KiB) Viewed 18183 times
IMG_7696.JPG
IMG_7696.JPG (277.33 KiB) Viewed 18183 times

Remove the mounting plate for it too:
IMG_7697.JPG
IMG_7697.JPG (269.43 KiB) Viewed 18183 times

With the intake and everything else out of the way, remove the cam chain tensioner. It's on the top of the cylinder.

Honda advises removing the EVIL BASTARD SCREW on the middle of the cam chain, then using their $100 tensioner (basically a tiny clamp) to keep it locked wherever it was before. You should totally do that. I didn't and it turned out fine. $100 for an ounce of metal is insane, and I refuse to pay for it. Even if I had wanted to use the tool, the tensioner tightener is underneath that philips head screw in the middle. At least on my bike, that screw was tightened by a pissed off gorilla on steroids. I couldn't get it off while it was still in the engine. I ended up clamping the tensioner to my bench and removed the screw with a hammer drill and a bit. You might get lucky and be able to just unscrew it. Anyways, I'll get to that when we reinstall it. For now, just remove the two bolts and pull the tensioner out.
IMG_7701.JPG
IMG_7701.JPG (267.73 KiB) Viewed 18183 times
IMG_7703.JPG
IMG_7703.JPG (243.98 KiB) Viewed 18183 times

Note in the second picture how the tensioner is fully extended. When it was in the bike, the piston looking thingy on the left was way more retracted into the housing. The Honda tensioner part that costs $100 (which is ludicrous) would hold it in place. Did I mention it's ridiculous that they want $100 for basically a tiny clamp?

I digress. Set the tensioner and its gasket aside, you'll worry about it again during reassembly.

Now that the cam chain is untensioned, remove the camshaft gear, behind where the water pump was, by removing the two allen screws.
IMG_7710.JPG
IMG_7710.JPG (208.12 KiB) Viewed 18183 times

It's difficult to remove, and even harder to reinstall later. Be patient, and don't force it.
IMG_7712.JPG
IMG_7712.JPG (245.46 KiB) Viewed 18183 times

The cam chain is secured in the bottom end, and you REALLY don't want to lose it down there. Put a zip tie or some string or something around it, so you can pull it back out of the bottom end if it somehow falls in.
IMG_7713.JPG
IMG_7713.JPG (210.93 KiB) Viewed 18183 times

It's time to remove the head. Unbolt the two long bolts that are below the water pump, holding the cylinder to the block.
IMG_7714.JPG
IMG_7714.JPG (269.26 KiB) Viewed 18183 times

Then remove the four nuts at the end of the studs that hold the rest of the cylinder and head in place:
IMG_7716.JPG
IMG_7716.JPG (277.95 KiB) Viewed 18183 times

Sliiiiiiiiiide the whole top end off. You might have to give it a few good tugs to get it started:
IMG_7718.JPG
IMG_7718.JPG (284.63 KiB) Viewed 18183 times

The piston will just flop down, and the chain will slowly sliiide through:
IMG_7719.JPG
IMG_7719.JPG (273.46 KiB) Viewed 18183 times

The old piston side by side with the new one. Phew, lots of carbon over the last 10k miles:
IMG_7723.JPG
IMG_7723.JPG (245 KiB) Viewed 18183 times

...To be continued. 8)
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
User avatar
dasshreddar
Frequent Poster
Frequent Poster
Posts: 755
Joined: Mon Oct 15, 2012 11:34 am
Year: forzaruckuspcx
Color: black
Location: central coast california

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by dasshreddar »

8) how to maddiedog. :D

Yeah that cam tensioner tool is B.S. after you get that Phillips head bolt out a simple small flat screwdriver works just fine for tensioning it back together.
User avatar
pcxpower
Regular User
Regular User
Posts: 397
Joined: Sat Aug 09, 2014 4:39 am
Year: 2015
Color: White
Location: Spain

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by pcxpower »

WOW!! I'm not sure that I would have the "cojones" to do this, but it's an EXCELLENT tutorial and, like the one meant to completely dismanthe the PCX, absolutely brilliant!!!! Of course, I'm subscribing... :D :D :D
Image
2015 Honda PCX 125
pcx125
Regular User
Regular User
Posts: 62
Joined: Tue Nov 19, 2013 4:23 am
Year: 2011
Color: White
Location: Australia

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by pcx125 »

That's very good How-to .
Have you done this before ? a big NO for me :)
User avatar
maddiedog
Benevolent Overlord
Benevolent Overlord
Posts: 3636
Joined: Tue Nov 01, 2011 7:04 pm
Year: 2011
Color: White
Location: New Mexico
Contact:

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by maddiedog »

I haven't forgotten about this how-to, just been super busy! I'll get to it eventually. :)
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
User avatar
pcxpower
Regular User
Regular User
Posts: 397
Joined: Sat Aug 09, 2014 4:39 am
Year: 2015
Color: White
Location: Spain

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by pcxpower »

No problem, and thank you very much for the very useful information! ;)
Image
2015 Honda PCX 125
User avatar
flyingzonker
Frequent Poster
Frequent Poster
Posts: 677
Joined: Sat Jul 12, 2014 9:20 am
Year: 2013
Color: Red
Location: Midwest USA

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by flyingzonker »

It's been a long time and still no conclusion to this tutorial? Did the project self-destruct? or what?
User avatar
maddiedog
Benevolent Overlord
Benevolent Overlord
Posts: 3636
Joined: Tue Nov 01, 2011 7:04 pm
Year: 2011
Color: White
Location: New Mexico
Contact:

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by maddiedog »

flyingzonker wrote:It's been a long time and still no conclusion to this tutorial? Did the project self-destruct? or what?
No, project is still good. The kit has 4k miles on it and runs like a bat out of hell. :)

I haven't had time to finish -- I will one day, I promise. :D
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
iceman
Forum Benefactor
Forum Benefactor
Posts: 2856
Joined: Sun Dec 29, 2013 11:43 pm
Year: 2014 125 (LED)
Color: White
Location: London, England

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by iceman »

I wonder - are you a self-taught home mechanic or a mechanic by trade? Simple tasks like the oil change, removing the rear PCX wheel I would have a go at, but this - this is a whole different leauge :)
Image
User avatar
maddiedog
Benevolent Overlord
Benevolent Overlord
Posts: 3636
Joined: Tue Nov 01, 2011 7:04 pm
Year: 2011
Color: White
Location: New Mexico
Contact:

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by maddiedog »

Self-taught. No one in my family is mechanically inclined at all.

I'm a Systems Engineer doing IT deployments for a living, and was just an IT guy before that. So... Computers all day, every day. I get to flip bits all over the place when I'm designing a network, but never can put my hands on the data. Mechanical tasks are fun because they're tactile; I get to get my hands dirty. :)
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
User avatar
maddiedog
Benevolent Overlord
Benevolent Overlord
Posts: 3636
Joined: Tue Nov 01, 2011 7:04 pm
Year: 2011
Color: White
Location: New Mexico
Contact:

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by maddiedog »

I'm on vacation, so that means I finally have time to continue this beast of a how-to!

At this point, you just took your head off the engine. You can look up into the head, the intake valve is the big one and the exhaust is the small one. After the combustion cycle, the hot gas has expanded and is under pressure, shooting the piston down. The exhaust valve opens, and the gas keeps expanding out into the exhaust system. Here's a view inside the cylinder looking up towards the head. The spark plug is the thing in the top center, exhaust valve on left, and intake valve on right. The plastic doohickey that hangs off the left side and came out from the depths of the lower end is the cam chain guide.
IMG_7722.JPG
IMG_7722.JPG (200.93 KiB) Viewed 17597 times

Take the head and cylinder over to your lab bench, where you have a nice clean pad to work on. Gently separate the head from the cylinder. There are a couple of little connection studs, make sure they stay with the head.
IMG_7724.JPG
IMG_7724.JPG (280.48 KiB) Viewed 17597 times

Below is the head, with the cylinder removed. For this kit, the cylinder gets replaced, but the head gets reused. Some kits replace the head too, and I kinda wish this one did as well. More on that later. You can see the valves closer up in this picture. The big slot at the top left is where the cam chain goes. In case I haven't mentioned it yet, the cam chain drives the camshaft, which opens and closes the valves at the right timings to get a good explosion contained to propel the bike forwards. The 8 oval-shaped channels around the cylinder area are the channels for coolant to flow. Everything here is dirty, and you can see there's coolant and bits of gasket on the head. ALL that needs to be clean and smooth to get good compression with the new gasket, so it all gets cleaned up.
IMG_7725.JPG
IMG_7725.JPG (285.96 KiB) Viewed 17597 times

Polish that head! Getting cleaner...
IMG_7726.JPG
IMG_7726.JPG (310.39 KiB) Viewed 17597 times

Shiny enough.
IMG_7727.JPG
IMG_7727.JPG (243.61 KiB) Viewed 17597 times

Check the new gasket for fitment. Mine blocks some coolant passages partly. This was my concern, and the reason I said I wished the kit came with a new head. :? It's fine 3k miles later at this point, so I'm confident this is good enough. Note the two connection stud thingies in the top right and bottom left. These sometimes come off with the cylinder, so make sure they end up with the head.
IMG_7731.JPG
IMG_7731.JPG (305.04 KiB) Viewed 17597 times

The next part has to do with changing the camshaft. You can skip all this if you're not doing a cam. I ended up not putting my camshaft in, but might put it in next time I do a valve check.


-------------- CAMSHAFT--------------

Flip the head so the valve side is down. Make sure the cam has the dot side up, or you can't wiggle it out. Here's what dot side up looks like on the side of the head (look at the dot at the top middle of the inner part of the camshaft at the middle of the pic).
IMG_7732.JPG
IMG_7732.JPG (287.22 KiB) Viewed 17597 times

Flip that head over again, and remove the two retaining bolts for the water pump collar:
IMG_7734.JPG
IMG_7734.JPG (267.96 KiB) Viewed 17597 times
IMG_7735.JPG
IMG_7735.JPG (278.9 KiB) Viewed 17597 times

Remove the bolt securing the camshaft. You can see the two cams and cam rollers at the top of this pic. The two rollers should look perfectly smooth, with no grooves. The cam chain rotates the cam shaft. The lobes on the camshaft roll, with the elevation changes opening and closing the valves in the engine at appropriate times so that air gets in, compresses, stays in to go boom, goes out, and then new air comes in. An aftermarket cam increases the time the valves stay open, sometimes having the exhaust and intake valve open for just a bit of time so that more air gets sucked in. More air = more boom! The caveat here is, engines like the PCX's are interference engines. They have 4 strokes (hence the name), which correspond to the 4 appropriate aforementioned times. If the valves stay open too long, they will actually hit the piston, turning your engine into an expensive paperweight. Anyways, I'm rambling...
IMG_7736.JPG
IMG_7736.JPG (291.51 KiB) Viewed 17597 times

You'll also have to detach the rocker arms that go to the valves, so loosen these two bolts too.
IMG_7737.JPG
IMG_7737.JPG (280.27 KiB) Viewed 17597 times

And remove the two bolts the arms pivot on:
IMG_7738.JPG
IMG_7738.JPG (260.24 KiB) Viewed 17597 times
IMG_7740.JPG
IMG_7740.JPG (246.46 KiB) Viewed 17597 times
IMG_7741.JPG
IMG_7741.JPG (267.67 KiB) Viewed 17597 times

Wiggle that camshaft out!
IMG_7743.JPG
IMG_7743.JPG (264.28 KiB) Viewed 17597 times

This pic shows an aftermarket cam next to the stock, respectively. I chose to leave mine out for now to see how the bore kit performs on its own, and may eventually add the aftermarket. Note the stock one, at the end of the camshaft, has a special spring-loaded lobe. This lobe rotates the cam when the engine stops to be in the optimal position to start immediately, and I think is called a decompression lobe. I'd say it's fairly essential to a PCX with idle stop, but it just means my PCX would be slightly harder to start. I left it off regardless. PCXdemon, our performance guru here, has assured me that the aftermarket cam would be fine without the spring-loaded lobe (you can mount it on there if you have a bearing puller, a press, and balls of steel that aren't afraid of accidentally destroying the camshaft bearings).
IMG_7747.JPG
IMG_7747.JPG (233.55 KiB) Viewed 17597 times

Reassemble the head in reverse order.

-------------- PICK UP HERE IF YOU'RE NOT DOING THE CAMSHAFT--------------

With the gasket in place, check fitment of the cylinder:
IMG_7749.JPG
IMG_7749.JPG (267.71 KiB) Viewed 17597 times

Remove the big black coolant hose from the side of the old cylinder. I totally forgot to take pics of that. It's just a basic clamp. The cam chain guide should just fall out too, take that out also.

Remove the coolant plug from the side of the old cylinder. Make sure you get the sealing washer:
IMG_7750.JPG
IMG_7750.JPG (267.02 KiB) Viewed 17597 times
IMG_7751.JPG
IMG_7751.JPG (240.36 KiB) Viewed 17597 times

Install the plug and the coolant hose on the new cylinder.

Place the cam chain guide in place:
IMG_7753.JPG
IMG_7753.JPG (251.28 KiB) Viewed 17597 times

At this point, you can place the cylinder on the head, carefully. Make sure the gasket sits flush, no debris is in the way, and that it is aligned perfectly. Secure the cylinder to the head using the cylinder head bolts. I did not see a torque spec, so be sane with your torque but make it good and tight.


Go back to the old cylinder and remove the two connection stud thingies:
IMG_7752.JPG
IMG_7752.JPG (277.09 KiB) Viewed 17597 times

And install those stud thingies in the cylinder. With the cylinder on and the cam chain guide in place, everything should look just like this:
IMG_7755.JPG
IMG_7755.JPG (251.34 KiB) Viewed 17597 times

Now time to go swap your piston!

Go back over to your engine, and get a pick in the hole on the side of the cylinder to pry out the circlips. You have to remove the circlips to get the piston's pin out to get the piston off the conrod. The circlips are a bitch to remove, good luck!
IMG_7756.JPG
IMG_7756.JPG (246.23 KiB) Viewed 17597 times

Yup, still picking away. Get a beer or two and walk away if you get frustrated.
IMG_7757.JPG
IMG_7757.JPG (255.66 KiB) Viewed 17597 times

ALMOST!!!
IMG_7758.JPG
IMG_7758.JPG (260.51 KiB) Viewed 17597 times

Now, GENTLY push out the piston pin:
IMG_7759.JPG
IMG_7759.JPG (238.02 KiB) Viewed 17597 times

The old piston, removed:
IMG_7760.JPG
IMG_7760.JPG (235.38 KiB) Viewed 17597 times

Now, we prep and attach the new piston.

At this point, some people gap the rings on the new piston. Google that if you want to, or check page 10-8 of the PCX Service Manual (2011). The kit was precisely to spec, so I did not have to gap mine.

The rings have to be installed in a very specific order, as shown in the close-up below, with the rings gaps offset as below:
IMG_7762.JPG
IMG_7762.JPG (307.74 KiB) Viewed 17597 times

The Honda manual is worth 1000 words:
IMG_7763.JPG
IMG_7763.JPG (301.14 KiB) Viewed 17597 times

Rings installed on the new piston. I made sure me, the rings, and the piston were all nice and oily to make sure no raw metal rubbed ever:
IMG_7764.JPG
IMG_7764.JPG (240.12 KiB) Viewed 17597 times

Before I install, one last look at the new piston vs old:
IMG_7765.JPG
IMG_7765.JPG (223.36 KiB) Viewed 17597 times

Slide the new piston on, and slide the new piston pin in:
IMG_7766.JPG
IMG_7766.JPG (264.34 KiB) Viewed 17597 times

Attach the terrible circlips. You should use new ones included in the kit. Make sure the gap does NOT line up with the cutout; rotate it until the gap is away from it.
IMG_7769.JPG
IMG_7769.JPG (267.54 KiB) Viewed 17597 times

Piston on! Note how I've carefully secured the cam chain so it didn't get dirty or fall into the lower end while I was working...
IMG_7770.JPG
IMG_7770.JPG (285.33 KiB) Viewed 17597 times

Put the gasket for the lower end on, and make sure it is sitting flush with no debris or anything blocking a good seal. Check the lower end to make sure it is clean and ready for a new gasket, cleaning off where needed.


Time to put the top end back on. Get a friend, you'll need him or her to guide the cam chain through as you gently put the cylinder down over the piston. Make sure to oil the inside of the cylinder before cramming the piston in.

Note that the cam chain tensioner is facing up (the round opening at the top of the cylinder).
IMG_7771.JPG
IMG_7771.JPG (305.19 KiB) Viewed 17597 times

You will have to carefully wiggle the piston and tighten the rings so the piston fits in. This is normal, take time and finesse, and has to be done right. You want all your rings to stay in place, both on their slots on the piston and in their 120 degree offset laterally around the piston. Note the 3rd hand using the zip tie around the cam chain to gently pull it through. You want to make sure during this step that the cam chain guide is sliding into the right spot in the lower end too, look at where it's going and make sure it looks right.
IMG_7772.JPG
IMG_7772.JPG (285.01 KiB) Viewed 17597 times

Finessing the piston into place:
IMG_7773.JPG
IMG_7773.JPG (268.8 KiB) Viewed 17597 times

And it should just sliiiiiide on down.
IMG_7775.JPG
IMG_7775.JPG (329.67 KiB) Viewed 17597 times

Tighten the 4 bolts on the head back up to spec, installing the washers first. Honda calls for 20 ft/lbs of torque, but indicates that you should oil the threads first. Keep in mind oiled threads take less torque to tighten the same amount, so use caution and do not overtighten or undertighten.
IMG_7776.JPG
IMG_7776.JPG (301.05 KiB) Viewed 17597 times

To be continued... 8)
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
User avatar
maddiedog
Benevolent Overlord
Benevolent Overlord
Posts: 3636
Joined: Tue Nov 01, 2011 7:04 pm
Year: 2011
Color: White
Location: New Mexico
Contact:

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by maddiedog »

Now that the head is on, we need to reconnect the top end of the motor so the valves can function and let the engine breathe. The valves are closed without the camchain attached, as they were when we first made sure they were way back during disassembly when the engine was placed at top dead center. Double check that the engine is still at top dead center. The notch should still be lined up with the arrow:
IMG_7777.JPG
IMG_7777.JPG (269.06 KiB) Viewed 17590 times

Whilst doing your best impression of a gynecologist given the extremely tight space, snake the cam chain gear back into the head, get the chain back on, and resecure the gear to the cam, ensuring the line on the cam is vertical and in its idle position. It should look like this when secured:
IMG_7788.JPG
IMG_7788.JPG (252.68 KiB) Viewed 17590 times

I should note here, it's REALLY hard to properly get the cam chain in there and on the gear, then secure. It will take a lot of delicate finessing to get in place. Be patient, and take your time -- you want to get this right or your engine won't run or will run poorly or will just blow up if the timing is too far off.

When the cam chain is on and secure, check the radiator fan again. The notches should still be in perfect alignment when the cam is in perfect alignment as pictured above. If it's not, you've put the cam chain on the wrong tooth of the gear. Take the chain off, rotate the gear a tooth, and try again. The lower end and upper end should both look like the previous two photos.

Before we rotate the engine over, since the engine is at top-dead-center, triple check your cam isn't upside down by wiggling the rocker arms like you would to check for top dead center during a valve adjustment.
IMG_7789.JPG
IMG_7789.JPG (315.5 KiB) Viewed 17590 times

While I was in there, I checked my valve specs and recommend you do the same. Mine were in-spec, as they have been ever since the first service. Note that ticking after this process is done usually indicates your valve cover gasket isn't sealing well or you screwed up the valve adjustment.

Now, to quadruple-check, rotate the radiator fan (recall it is attached to the crankshaft directly) 360 degrees. Nothing should bind, but the engine may put a bit of resistance from compression. Keep going another 360 degrees for two full rotations. Nothing should bind, and your engine should be back at top-dead-center. Check your cam and rocker arms and fan alignment one last time, then move on.
IMG_7790.JPG
IMG_7790.JPG (313.48 KiB) Viewed 17590 times

The cam chain at this point may be a bit slack, because the cam chain tensioner is not attached. That's the doohickey that goes on the hole on the top of the cylinder that looks like this:
IMG_7791.JPG
IMG_7791.JPG (234.06 KiB) Viewed 17590 times

Ok, so time to rant on this... The cam chain tensioner is just that -- it tensions the cam chain. Behind that hole on the top of the cylinder is the upper cam chain guide. The cam chain tensioner is a fancy wound spring that puts constant outwards pressure through the springs, but is unable to retract, ensuring consistent tension on the chain. That means your tensioner right now is locked fully outwards. If you press on the part to the left, nothing happens! Madness! The stock Honda tensioner tool, which is a $100 screw and nut, are designed to hold the tensioner in exactly the position it was in when removed to allow easy reassembly. Well, $100 is ludicrous for a tool that you'll use once. Remember this picture?

Image


In it, you can see the cap over the tensioning screw. It will be factory overtightened. Remove the cap in the middle of the top of the cam chain tensioner. You may have to use an impact gun (I'm not kidding).

At this point, you can see the middle of the tensioner, including a tiny little winding screw in the middle. The tensioner uses a helical spring, which you can rewind to retract the tensioner! WOO! Ok, I'm getting too excited (but seriously, I figured this crap out and it saved me $100 on the stupid Honda tool, and might save you that too). Stick your tiny screwdriver in there, and tighten it. The tensioner will wind, and the rod holding the tension on the cam chain guide will retract, as you can see below:
IMG_7792.JPG
IMG_7792.JPG (239.88 KiB) Viewed 17590 times

Now, the only problem is, the SECOND you remove that screwdriver, the tensioner fully extends, ruining all your hard work. So either grow two extra arms, or find a friend. Whilst holding the tensioner in full tension, bring it over to the cylinder. Have your friend install the new gasket for the cam chain tensioner, and, still holding the tension, place it in place. KEEP HOLDING THE TENSION FULLY while your friend tightens the tensioner into place. The only thing the Honda tool is for is allowing you to solo this part. Tis silly.

Here's what it looks like, me holding tension like a boss and installing it in the PCX:
IMG_7794.JPG
IMG_7794.JPG (227.35 KiB) Viewed 17590 times

Once it's fully seated and tightened, slowly let the screwdriver unscrew as the tensioner seats. It shouldn't unscrew too far, it should only unscrew a bit. If it unscrews as much as it took to screw to retension, something is very wrong with your cam chain or tensioner.


Put the valve cover on, putting a dab of sealant at the corners of the water pump (the valve cover is prone to leaking there). Make sure you don't overtighten. The post-2011 PCXes have 4 valve cover screws, but this one only has 3, so if you mess one up, you're going to have a bad time. (as an aside, I accidentally broke one of the valve cover bolts on Mel's wife's PCX. It doesn't leak at all, so the 4th is important, but not needed, on the post-2011 PCXes).

Start connecting everything. Connect the electronics, throttle, and fill up coolant. Somewhere in there I also hooked up the radiator hoses to the new cylinder and everything else. Just reverse the reassembly. Make sure no connector goes unconnected.
IMG_7795.JPG
IMG_7795.JPG (274.64 KiB) Viewed 17590 times

Make sure you hook up the throttle cable right. I didn't, and nearly went for an involuntary ride around the neighborhood when it ROARED to life the first time.
IMG_7798.JPG
IMG_7798.JPG (301.83 KiB) Viewed 17590 times

Finally, bleed the coolant system or you'll get an overheat warning. You will have to rebleed after starting it the first time too. Here's the pages from the manual:
Screen Shot 2015-05-05 at 4.35.39 PM.png
Screen Shot 2015-05-05 at 4.35.39 PM.png (188.84 KiB) Viewed 17590 times
Screen Shot 2015-05-05 at 4.35.50 PM.png
Screen Shot 2015-05-05 at 4.35.50 PM.png (234.27 KiB) Viewed 17590 times
Screen Shot 2015-05-05 at 4.36.02 PM.png
Screen Shot 2015-05-05 at 4.36.02 PM.png (230.77 KiB) Viewed 17590 times

I should note that I had to bleed my coolant 3 times before all the air was gone, so don't go into full panic mode or drive far from home until you're 1000% sure your system is free of air.


Hook up your battery.


Wheel the PCX outside and, with your finger next to the kill switch in case of disaster or weird noises or mistakenly putting the bike's throttle cable at the wrong angle so it starts at full throttle (I'm in no way guilty of the last one), crank it up for the first time.
IMG_7801.JPG
IMG_7801.JPG (369.26 KiB) Viewed 17590 times

SHE'S ALIIIIIVE!!!! HAHAHAH!!
IMG_7802.JPG
IMG_7802.JPG (455.51 KiB) Viewed 17590 times

To check for any issues, take it for a couple of laps around the street before buttoning her back together. I advise wearing gear. I was a bit too enthusiastic to bother.
IMG_7806.JPG
IMG_7806.JPG (271.98 KiB) Viewed 17590 times

You're DONE! ...Well at least with the hard part. Put the rest of the bike together, and break it in using whatever method you think is most appropriate, but remember that extended full throttle on a new engine is bad for it. You should vary your throttle constantly.

I ran the bike for about 10 miles, changed the oil (it had some gasket and a bit of extremely fine metal glitter in it when I did), then ran another 500 miles before changing oil again. During those 10 miles, I had to rebleed the coolant system a few times, and the hot light came on once since the water pump was sucking air. After filling and refilling, all is 100% normal now.

After several thousand miles, I've noticed the kit gets oil dirtier faster than stock. Given I'm putting way more load on the PCX by using this kit with a gear up kit to cruise at 65mph or so for extended periods of time, I now do oil changes every 2500 miles as well. We'll see how long this kit lasts. I have gotten almost 3k miles out of it so far, and it's going strong still. About 50% of my riding is at 65mph when I'm commuting. I get about 85mpg now.


That concludes the longest, and most indepth how-to I've made. Just like any of the others on the site, if you have any questions, ask away, and if you found this site or how-to helpful, you can buy me a beer (probably more like diapers at this point) using the yellow DONATE button at the bottom of the page.
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
User avatar
kramnala58
Mod Emeritus
Mod Emeritus
Posts: 2864
Joined: Sun Jun 09, 2013 7:49 am
Color: White is faster
Location: Niagara Falls, USA

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by kramnala58 »

Hey Dave, "vacation" or "staycation". ;) ... Either way, enjoy the time off.
2010 Honda PCX 125 in Thailand (White) - "White Lightning" Sold in Sept 2017 :(
2009 Yamaha Majesty YP400 in USA (Metalic Titanium) - "The Throne" Sold in June 2020 :(
User avatar
maddiedog
Benevolent Overlord
Benevolent Overlord
Posts: 3636
Joined: Tue Nov 01, 2011 7:04 pm
Year: 2011
Color: White
Location: New Mexico
Contact:

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by maddiedog »

Vacation! Just got home though. We spent a week in Ormond Beach, Florida. :D
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
User avatar
Oyabun
Frequent Poster
Frequent Poster
Posts: 640
Joined: Sun Jun 28, 2015 4:24 pm
Year: `12,`15,`19
Color: black&black
Location: Europe

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by Oyabun »

Maddie,
Are you using the stock spark plugs after installing the kit, or Takegawa has recommended different heat range?
Have you checked them how they read since the installation?
Thanks
Tamas
User avatar
maddiedog
Benevolent Overlord
Benevolent Overlord
Posts: 3636
Joined: Tue Nov 01, 2011 7:04 pm
Year: 2011
Color: White
Location: New Mexico
Contact:

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by maddiedog »

Tamas, I used the stock plugs. The instructions don't mention any change in spark plug.

I didn't check them, but I got about 2k miles on the PCX before I sold it. It was running strong and quick when I sold it, so I don't think a plug change is needed.
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
User avatar
power-full
Regular User
Regular User
Posts: 271
Joined: Sat Jan 21, 2017 6:42 am
Year: 2010
Color: preta
Location: paio pires seixal portugal

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by power-full »

good, have you used or installed any electronics ".. without rpm cut or injection change" or any such device?
just assembled the pieces that are in the photos?
What was the speed difference?
speed variator use the source?
valve springs changed?
sorry to be asking these questions all but wanted to buy a kit of these and on the site I see that one should change the electronica of the motorcycle and that for me is very expensive €€€€€ lol
https://www.facebook.com/sergiofininho
Pcx powerfull kit yuminashi 168cc
93000km 23.03.2022 dont stop..
User avatar
power-full
Regular User
Regular User
Posts: 271
Joined: Sat Jan 21, 2017 6:42 am
Year: 2010
Color: preta
Location: paio pires seixal portugal

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by power-full »

hi hello .. this week I want to see if I'm the one next to mount my yuminashi kit on my pcx.
  is the complete 164cc kit, I'll also fit the final gear kit, the AFR (injection driver). as well as the gasoline injector of greater debit "tuning of model honda cbr 150cc" and inercia power boost .
I will try to insert here the references of the material, my pcx is a 125cc 2010 model of the jf28 engine.


38772-KWN-000A YUMINASHI FUEL-ADJUST CONTROLLER (5-PIN TO 5-PIN),
https://www.facebook.com/sergiofininho
Pcx powerfull kit yuminashi 168cc
93000km 23.03.2022 dont stop..
User avatar
power-full
Regular User
Regular User
Posts: 271
Joined: Sat Jan 21, 2017 6:42 am
Year: 2010
Color: preta
Location: paio pires seixal portugal

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by power-full »

hi hello .. this week I want to see if I'm the one next to mount my yuminashi kit on my pcx.
  is the complete 164cc kit, I'll also fit the final gear kit, the AFR (injection driver). as well as the gasoline injector of greater debit "tuning of model honda cbr 150cc" and inertia power booster .
I will try to insert here the references of the material, my pcx is a 125cc 2010 model of the jf28 engine.


YUMINASHI FUEL-ADJUST CONTROLLER (5-PIN TO 5-PIN),38772-KWN-000A



44T FINAL GEAR SPROCKET SET, COMPLETE WITH SHAFT (PCX125 / SH125i)
23430-KWN-440



INERTIA POWER BOOSTER SET 15431-KWN-000



164CC LIGHT BORE FLAT DECK CYLINDER KIT (PCX125 V1) (FOR 125CC HEAD) 12103-KWN-600XA

Honda CBR 150 Keihin injector assy (Tuning CBR 125)16450-KPP-T01
https://www.facebook.com/sergiofininho
Pcx powerfull kit yuminashi 168cc
93000km 23.03.2022 dont stop..
Pcxdemon
Frequent Poster
Frequent Poster
Posts: 926
Joined: Mon Feb 20, 2012 7:13 am
Location: Gold Coast,Australia

Re: How-To: Install a Big Bore Kit (Honda PCX 125 non-eSP)

Post by Pcxdemon »

Must get 150 head too ideally, it has bigger valves and ports. Deff more power and less chance from overheating. Also get yourself forza 35mm TB its awesome and its a straight fit. If you chose to keep 125 head, then you must do this...In the maddies photos above you will see a photo of a 125 head water ports with a 170 head gasket aligned on the head. You will also see that the 170 or for that matter 164cc cylinder ports from the head gasket don't align properly with 125 water ports. Do the same mock up and then use a black marker and colour in the metal on the 125 head water port that doesn't align any more. After that use either a dremel tool or a small file and process those ports biggest to align properly with the head gasket. Its very easy to do. After that you shouldn't have any more troubles with overheating. Also Install the plug Yuminashi specifies as that will actually run your motor few degrees cooler. I know as i have water temp meter and it clearly shows the difference.
Post Reply