The Honda PCX / Forza / ADV150 / SH Forums

search on here under "has anyone had their seat fixed under warranty"....scan through the entries...simple solution to the issue is shown. Done this on my Forza a few years ago and never had a problem since.

23.000mls from new on my 2014 Forza NSS300 and never even looked at the valves. Bike runs as sweetly as when new...so my view is dont fix unless broken.

At the Forza 300 last MOT ( UK annual inspection requirement) one of the "advisory " comments was "Brake hose has slight corrosion to "ferrules".rear brake hose..) Any advice on ... 1...does this mean I should consider renewing the hose?...or is it possible to just renew the...

Dave..if reusing same nut perhaps I should have used a little locktight?

you are of course correct Dave..and like you I have just reused the existing 4 times now...does a replacement nut have some sort of "locking" on it which is broken when unscrewing? being the reason for the guidance to always use a new one?

thanks Whitenoise...still looking on this site almost every day...but, as I do in life, I only make input when I have anything useful to ask or say. The update is that I had a good look at the back wheel area and guess what. The wheel bolt was slightly loose !!..must have been my fault when last cha...

Austins...thanks for sourcing and posting that interesting article...and thanks all others also
Sounds very likely its all down to a loose wire/connection in the ABS system someplace as some suggest.Will take time over our winter months to examine as much as I can . thanks all.

thanks again for responses No... not done any power slides !!..not even sure what they are !? have always used the same tyres make as supplied with the bike On page 20-8 in my copy of the full service manual it does say that incorrect tyre pressures can cause the blinking/flashing. along with a load...

thanks Jge for the suggestion Will check this...but I had inflated both tyres just before going on the ride and it would have been 50/60 miles riding after that before flashing starts...but will check pressures....may have a small air leak? I think it is in the bike handbook or the service manual wh...

Any advice or comment will be appreciated Couple of weeks ago while out riding the ABS light started flashing on my 2014 Forza NSS300 . Searched for advice when back home and found somewhere advising ( may have been on here?...cannot remember) that if you turn the engine off and start it again the l...

Hakamin...5ft 10ins...and yes ride looking over the screen.

I have the PUIG one on my 2014 Forza and it is excellent. While I ride looking over the top of the screen I suggest you dont go for the dark tinted one, as I have, as in certain light conditions it is difficult to see downwards through it for near kerbs etc . There is a light tinted one which may be...

Brilliant Mike!!...need to get yourself out to Thailand and get the wife and two kids on it along with the dog.!
But well done and designed.

Did mine on my 2014 Forza about 2 months ago George as I noticed it was sticking and not retracting fully..It looked identical to yours.I think this is something all owners should look to do slightly more often than my 6 years/20,000mls from new. Perhaps every 3/4 years/10,000mls? The bit I found di...

update for interest/information...
put the old front pads back on ( still a bit of wear left in them)...and no pulsing or noise experienced. Gave it a good trial.
So...I conclude its the new pads causing the pulsing/noise ?
Examined the new pads closely but cannot see any issue with them..

update for interest/information...
put the old front pads back on ( still a bit of wear left in them)...and no pulsing or noise experienced. Gave it a good trial.
So...I conclude its the new pads causing the pulsing/noise ?
Examined the new pads closely but cannot see any issue with them..

yes I am starting to wonder if its the pads themselves...but just bog standard EBC Organic scooter pads which I have always used. Beginning to go off the thought that its the caliper as answering points on here...gn2 and yourself... has made me think clearer. As I get the sensation /noise when apply...

wheel bearings?...would that not have a noise independent of engaging brake...ie a noise when wheel was turning as opposed to when braking. and I am not convinced there is anything wrong with the disc as there was no noise or pulsing until the brake pads were renewed. Would a warped or unevenly worn...

thanks gn2 but have already done that...twice...and no change in the problem...not even an improvement...so thinking that the problem just has to be with the caliper pistons somehow...because I cannot think what else it can be..It is not the disk...the only thing left to try is a total service of th...

of course a typing error!!...18500mls..